Finished my b16 92 hatch!

[Mini Prime]

Hell yeah I just finished this week my b16a2 swap ed 92 hatch. I freakin love it alot of hard work cause i pulled two motors and then put the b16 back in , in 2 days 12 hour days working, but it was well worth it . I will post pics tonight or tomorrow. I have to gwet the valves adjusted they seem to be loud when i accelerate.hmmmm anyways i have a virgin p28 in the car right now is thier any advantage to have the p72 in or should i chip what i have or just leave it alone .

[civicracing98]

DOUBLY PoST! :shock:

[Mini Prime]

http://www.imagestation.com/mypictures/inbox/view.html?id=4132409180&url=http%3A%2F%2Fwww.imagestation.com%2Fpicture%2F sraid146%2Fp9e56bdb70fe026a7f69fbd3f5b99f418%2Ff64 f8f5c.jpg&caption=Sean%27s%20Civic%20028 this is the engine right after I dropped it in.

[Mini Prime]

wow I can't get the pics to work...

[J32a2OwnsU]

No pic for me....Just a Red "X"

[rei]

wow that engine looks quite similar to a red x.. anyways congrats on the swap.. cant wait for mine..

[toanhung]

you should chip the p28 for the p30 program. because the p28 don't have the right ignition and fuel map for b16a. as for the p72 it for gsr motor it have the fuel map for dual butterfly . p72 better then p28 but p28 chipped better then p72 for you current motor

[Mini Prime]

http://img.photobucket.com/albums/v517/miniprime/SeansCivic028.jpg

[Mini Prime]

http://img.photobucket.com/albums/v517/miniprime/SeansCivic042.jpg http://img.photobucket.com/albums/v517/miniprime/SeansCivic045.jpg http://img.photobucket.com/albums/v517/miniprime/SeansCivic043.jpg more pics of my car

[mycarisslow]

niec swap. i like the red accents. btw, is that a sony hu in the car?

[Mini Prime]

yeah it came with the shell when i got the car

[civicsi94]

nice ride homes. she is a beauty and clean. Congrats on ur swap. So what are the future plans for ur baby?

[Mini Prime]

well my plans right now is to finish getting the bugs worked out on the motor just running into the common problems when you swap I think i am just going to bring it to my local honda dealer and just tell them to do a over all tune up and check everything out. One thing i am stumped on is that i put 95 gsr axles on the car and i already see a little axle grease on my passenger side hmmm why would it already loose some when they are brand new i can use 95 gsr non abs axles right?

[doug piston]

looks good but lose that ugly exhaust manifold

[JL]

looks good but lose that ugly exhaust manifold

And clean up the block.

[Mini Prime]

yeah i havve the block cleaned up now that was right after i goot it back in just need a header think i might go with comptech instead of dc dc is cheaper in price i believe and just as good

[norcal_civic]

Nice. I know it has nothing to do with the engine, but I really like the black GSR rims.

[EG_CaSe]

http://img.photobucket.com/albums/v517/miniprime/SeansCivic042.jpg http://img.photobucket.com/albums/v517/miniprime/SeansCivic045.jpg http://img.photobucket.com/albums/v517/miniprime/SeansCivic043.jpg more pics of my car


quick question... where the fuck did you find them fog lights?? ive been lookin around for a long time i only seen then for a 92-95 4door r if i found them for my bubble there asking way to much 150+

[Mini Prime]

When I bought my 94 ex coupe they where on it so i have no clue where the kid found tham

[PBzAllan]

thumbs up on your swap pats your back*

[EG6/B16A2]

Did you have the same problems? This was a post i had put up a few months ago.

A 00 civic SI engine (B16A2) an OBD2 which when I got the motor it had the stock wiring harness with it, but I have a 92 civic hatch CX which is an OBD1 vehicle, but it’s always easier to convert backwards rather than forward... (OBD2-OBD1) rather than (OBD1-OBD2) right? So thinking that what I did was get a 95 civic EX wiring harness which is OBD1 with a 95 GSR dizzy which is also OBD1, also 95 GSR injectors and a 95 P72 so it would become plug and play. For the most part it worked it ran good but I was concerned about my dizzy because I had to advance it all the way forward to match up my timing to stock specs (used a timing gun) but I never adjusted the cams or even took the valve cover off, so what I assumed it was, was the GSR dizzy (OBD1 right?) but im no expert I have only done a few swaps and we never converted OBD’s before so this was a new project. But I must say the motor ran good but I don’t think we got all the potential power out-put and No the engine is totally stock and I have never played with the cams at all but we had the dizzy set in the middle where it should be at stock specs but I was burning plugs left and right so we checked the timing with a timing gun and found it was off so we adjusted the timing by way of the dizzy and according to the timing gun the timing was right on when the dizzy was advanced all the way forward and the car ran 100 times better i stopped burning plugs but I still wonder about the dizzy so far advanced...? So I have been looking all over different sites to see if anyone else has done this swap also so I could get some insight. Justin...

[KINCHEE]

lookin good. great swap

[Prez]

thumbs up on your swap pats your back*

who is that in your sig? thats one of the nicest air chairs ive seen...

[efren3]

looks good dond like the red on the walve cover

[o0kuam0o]

Gray interior :cry: you should get a black ex or si dash and doorpanels..

[zville00SI]

So how are the lifters coming Mini Prime, did u get them to quiet down any??????

[Mini Prime]

yeah i had a valve adjustment done sounds good now. I just have to replace the dam iacv its bad and my car is running rich other than that i beat a 2003 eclipse spyder which was fun as hell the guy looked pissed when i left him in second gear. hahahahah this car is going to get me into more trouble than i need.

[ixwesleyxi]

congrats on the swap...looks good

[rUdGrICk]

Hell yeah I just finished this week my b16a2 swap ed 92 hatch. I freakin love it alot of hard work cause i pulled two motors and then put the b16 back in , in 2 days 12 hour days working, but it was well worth it . I will post pics tonight or tomorrow. I have to gwet the valves adjusted they seem to be loud when i accelerate.hmmmm anyways i have a virgin p28 in the car right now is thier any advantage to have the p72 in or should i chip what i have or just leave it alone .
yo p28 has the most potential out of all vtec ecu;s..yo chip it and ull love it,btw nice ride