Search results

  1. sikswic

    95 civic idle issue help

    Could be a bad iacv, could also be a vacuum port. I had the same problem with my y7 swap and I figured out it was a little tiny vacuum port on my intake that had no hose on it, i swapped my intake cause it didnt have a the same vacuum port or you can cap it off. Theres a lot of trouble shooting...


  2. sikswic

    2000 Honda Civic Dx Project

    just a dd so far. were going to do another shoot with a local shop and his boosted eg. ill post pics up tomorrow
  3. sikswic

    2000 Honda Civic Dx Project

    First photoshoot ever with my buddies. My 2000 honda civic dx Friends had a 98 honda accord j30a1 and the other a 2011 impreza 2.5i
  4. sikswic

    What is this tick? Spun bearing?

    check and see if one of the valves broke. thats what happened to mine and i think i spun a bearing also. doing a 50 ft burnout off the rev limitor isnt a good thing and my car lasted 3 weeks before losing all of its compression driving 60 miles/5 days a week. start looking on ebay for a new motor
  5. sikswic

    Somewhat new to honda

    Niceee!
  6. sikswic

    Somewhat new to honda

    :nopics: Just kidding! post some pics up and congrats! did you buy it as a project or daily driver?
  7. sikswic

    2000 Honda Civic Dx Project

    I plan on getting lips, getting new doors and fenders cause they are dented and then im thinking of getting a fresh paintjob. Then during the wintertime im going to do another swap but put in either a b16 or h22
  8. sikswic

    2000 Honda Civic Dx Project

    *UPDATE* My cars been running mighty fine. Compression is good and it feels good to know I did my first swap with no problems. Also decided to paint my valve cover and carved some stupid s**t into it. Probably will repaint it but I dunno. Next up is to fix up my stock rear bumper and...
  9. sikswic

    engine swap confusion

    This might help a little... http://www.clubcivic.com/board/showthread.php?t=196671 Also i believe your engine is a d16y8, so just swapping the same engine in would be cheaper. If you swapped any other motor in, for example a b16 or any other dohc, then you would need an engine harness...
  10. sikswic

    Starting to think about rotors

    I believe so. I took my hell screws out by drilling them since I stripped them out, took a little while but they budged and then I just sanded down the excess metal that was left behind cause my rotor wouldnt seat properly


  11. sikswic

    where is the a/c expansion valve located?

    Ohh haha my bad. Sorry. I dont know much about a/c
  12. sikswic

    where is the a/c expansion valve located?

    Could try adjusting your clutch pedal. what have you done to the tranny? you need to give us more info
  13. sikswic

    D16y7 vacuum port

    I looked but couldnt find anything about it, i even googled it. I swapped out my intake manifold and now its running perfectly. Its amazing how such a small stupid thing like that can ruin your day after a swap haha
  14. sikswic

    D16y7 vacuum port

    Im going to try switching the intake
  15. sikswic

    D16y7 vacuum port

    I did an engine swap, just another d16y7. Its my first and im having trouble with my idle. Icv is good. im pretty sure the vacuum port in the picture needs to get past the fire wall and go somewheres but my original engine didnt have that port. Is there any way I could delete it or make it...
  16. sikswic

    What are you doing / did you do today / CHAT THREAD

    Is this how the retention clip sits in the release lever or is it the other way around?
  17. sikswic

    Retention spring position?

    Y7 tranny. Is this how its supposed to sit on the release lever or do I flip it around?? Any help would be appreciated
  18. sikswic

    Sensor and bolt position

    Sooo im doing my first swap, just another y7 to get it back on the road, and was just curious of what sensor that is in the pic at the top and obviously it looks as if someone before snapped the head off a bolt to the bottom right circle but i just wanted to see if theres supposed to be a bolt...
  19. sikswic

    What are you doing / did you do today / CHAT THREAD

    Anyone go to syracuse nationals??
  20. sikswic

    2000 Honda Civic Dx Project

    The swap is a very slow process. Just have to pull the axles out and then the engine. I still have a lot to work on. Gotta swap everything off the old to the new also. Its been a very stressful week so im trying to layback from it and relax but I also need to get it done asap. Not sure what im...
Top