Search results

If one of your codes is a p1299 its most likely your ecu. I had a similar problem yet the car ran fine but the cel would flash if i would rev past 5k. replaced the ecu and no more cel or random misfire or misfire in all cylinders.

I get certi fit for 30 a bumper. fits pretty dam good too. helps having an account with the local warehouse

I always use dayco from atuozone. just did the timing belt and water pump on my brothers camry and I ordered the kit (belt, water pump, pulley, and tensioner) all for less than a hundred bucks. all Dayco. Same kit is on my car (except its for honda of course) and I havent had any problems. Dayco...

koni yellows have adjustable perch heights. that way you can go lower without coilovers

You need to remove any serpentine belts that are still on the car. Once those belts are off you need to remove the harmonic balancer. Once thats done remove the valve cover and remove the timing belt covers (top and bottom). Place a small jack with a piece of wood on top of the jack under the...

soooo have a few updates and more to come now that school is over for the semster. Started my own repair buisness for some extra cash on the side and I was suprised how quickly it grew! I literally have to hand jobs off to my coworkers (since i still work at Auto Zone). But onto the fun stuff...

Get a dead blow hammer and tap the inner piece of the CV axle while rotating it slightly. Also hold the shaft and push it inwards while rotating it and tapping it with the hammer.

:lol: i just had to. a car thtats caught my eyes multiple times is the 90's BMW 318i. wouldnt mind an early 00's z3 M trim. If only BMW didnt stand for breaking my wallet.......

or battery. get it tested at a parts store before you buy a starter. they test batteries for free at parts stores. I work at auto zone and ive seen people throw parts at their cars and finally realize it was as simple as a blown fuse. not in your case though. start from ground zero which is the...

if you dont care about your turning radius, your tire size will be roughly (205-215) (less than a 40 series) and of course r18

how many miles have you put on your engine and are you n/a or boosted? just curious how your motors runnin since you built it.

Im kinda stumped at the moment. Im gonna be purchasing new internals for the extra motor that im building up. Its gonna be for boost, but the boost will be in the form of a supercharger. Im wanting to do a mildly high compression build for now, get that tuned, and then move on to installing the...

aint there a bolt to adjust that??? lol

its just lower control arm. i had the same problem with my car. fairly inexpensive fix but get an alignment once you replace it. honda is actually the cheapest for an alignment. at least a good alignment.

Sooooooooooo back from the dead. School and work have been killin me since i work a full time schedule and go to school full time. anyways, its payin off since ive gotten new goodies!!!! finished the rear disk swap, and finally got some new(ish) tires and hubcaps till i can get new tires for my...

ive looked at multiple different rotors with 4x100 lug pattern. the BOLT pattern is what needs to be redrilled. not drilled and slotted rotors. i looked at the miata and honda fit rotors and theyre not the same dimensions. The rotors have to be the same diameter and thickness as the ITR rotors...

Im doing a big(er) brake upgrade on my car using the prelude rotors, itr brackets, and legend calipers. The only problem ive run into is where can i get the rotors redrilled from a 4x114 to a 4x100 bolt pattern? I know i can do it myself with a drill press, i would just rather a machine shop do...

And yet it keeps the engine bay cleaner and makes it easier to actually clean the engine bay. and anyways. ricers only know about chrome and neon paints. :lol:

Koni yellow struts with d2 springs. On the front struts put the adjustable collar on the lower perch. this settles the ride height to a more even appearance. I cant complain at all about the suspension. Ive had it set on "sport" and Its not too rough, and isnt bouncy at all. I get compliments on...

Gave myself a hair cut (Im just that ballin). tapped and rethreaded one of the bolts for my valve cover, then put it all back together with some wonderful honda bond. Stopped by work for the christmas party and of course ate too much since it was all free. Then went out for dinner with some...