Search results

A proper retrofit is going to run $300+ doing a DIY depending on the quality. $70 sounds like he's gonna drop in some eBay specials he got for $20-30 and profit the rest. doing the P&P is really easy. so he is probably raking in cash from the dumdums taking him up on the offer.

Ignore him. they are rock chips in your case. it's called sand blasting or sand blasted. Commonly seen in high mile highway cars. My car was resprayed by the PO, but the windshield looks like your hood from the constant nicks from road debris. Quick answer, hood bra to cover it. Long answer is...

I had the same problem with my 2000. Find a cup holder section from a 96-98. They are 1000000% better. the ones with the flip up lid. they should be swappable. not 100% sure but pretty sure. I'm running a 98 center console in my EG for this very reason. Worst case, just swap the whole ,lower...

I have the eBay stick ons and they are not going anywhere. if you clean the matting area on the door properly (alcohol) and scrub it down good to get all the loose residual grease/grime/etc off of it and install the visors on a warm day, they will stick on and adhere pretty good.

Before I start, I know, it's your car, do what you want, but, are you sure you know what parking lights are? Moreover, why would you want to illuminate those lights with a higher intensity lamp? I am gonna take a wild stab here and think you are talking about the DRLs. You can, but it'll be a...

If you buy that, I have some UBER RARE blinker fluid for you.

x2

Honestly, it should take a good half-day to a day especially if yo have a extra set of hands. It took me a little over a month because of time constraints with work and my work hours.

I have the EK center console from cup holder to armrest in my EG. I LOVE IT. Actual cup holders and a big armrest. There wasn't much modding to do. Just trimming the top of the front section of the EK console to fit around the lower part of the EG console. Then I screwed the front of the EK to...

PLEASE NOTE: I am not giving exact measurements. I am giving a guide on how to build your own. This write up is open to interpretation. Also, not every step is pictured, I did this all by myself during odd hours and didn't always remember to stop and take pictures. OK, so I finally got enough...

The part is available, you were just looking in the wrong trim level. If you check the DX trim, it'll show up. As far as the console being loose, I don't see any bracket that it bolts/screws to in the rear. just make sure that it's bolted to the front half of the console. I think you may have...

Winner winner chicken dinner.... Anyway, I think he is talking about a "type R" red carpet. similar to this one. Also, OP, post pics. it helps with visualizing your description.

Have you checked the FIRST things to check like, thermostat, temp sensor, rad fan?

Stock = goofy (to you) Halo's = played & ugly (to all others) Drop in HIDs = Horrid and other want to kill you (to all others)

And you want to trust a site you've heard bad about? Just do HMotors like suggested above. They have been in the game for a long time and sell good stuff. :word:

http://www.1aauto.com/ Thats where I got mine. Cheap and quick shipping. I've had mine for almost a year and no issues. Reuse your fan if it works, no issue.

http://www.ej8squad.com/thread-11906.html

If you searched and didn't find anything, you didn't look hard enough or care to look hard enough. Start here: First H-T link- the one with lots of pics Then 2 pages in THIS gem pops up. Like I said, there is no one DIY written that takes you from start to finish. With all the DIYs out...

No, left to left right to right, the position of the motor is designed for a specific side due to door designs.