Green's EH2

[Steven.]

pics thread for my hatch.

when i first picked it up:

Painted the bumper support and the rad support:

Motor i was going to swap in:
B18b1

Engine i just got out of a junkyard, FOR CHEAP!
OBD2(99 i think) B18c1/w GSR S80 Tranny

plans for the engine right now.
Re-ring, AEBS manifold, hondata intake gasket, ARP Head studs

had the engine in my garage for a day, couldent wait any longer so...

in it went

did a small wire tuck(big connectors and head like area)

then i pulled the GSR head, to get ready for new rings to go in.

more pics and s**t later

 

[Silver Bullet]

coming out nice...hopefully u can get to run this soon

 

[Steven.]

Car Specs and mods(current and future)
(current)
95 Civic DX hatchback
$50 Paint Job(white)
Flat black Engine bay
GSR Fat fives
B18c1 engine swap
DC sports 4-2-1 1 piece header
RX-8 front seats

(future)
OEM style Yellow Fogs
some sort of front and rear lip
new springs
tires(have 2 already)
new dash
Rear disk
amber corner lenses or JDM ones
AEBS manifold
gloss black roof,hood, and hatch(till i buy CF hood and hatch)

 

[Steven.]

coming out nice...hopefully u can get to run this soon

should be running by the end of the month, the engine at least, i cant drive till april

still need some parts for the engine, oil pan, dissy, axles, shift linkage.

 

[dank24]

wow that head is clean

 

[Steven.]

forgot to add to that list:
Fastline Performance Oil Pan Baffles

 

[chow]

looking good already.

 

[Suanico]

1st motor looks like it sat in the rain for a while, how much did you scoop the gsr swap for? and you can run the win on the block on car fax to see what year that motor is

 

[12.8:1 Ls/vtec]

He can just look at the head to see if it is stamped p72-1 or p72-2, the 1 is for obd1 and the 2 is for obd2. I'll doubt he cares beyond that.

 

[Steven.]

p72-2
i already knew it was OBD2, the harnness on the engine is a OBD2 harnness, and it was already swapped when i got it.

 

[Genuine Rolla]

wow...nice progress so far man. keep up the good work.

 

[zach246]

hey how did tie the wires to the fender like that? i see you used clips but wat are they exactly? im asking cus i did a tuck the same as you and im tryin to fidn a way to keep them tied like that

 

[Steven.]

zip tied it to the hood latch cable

 

[somejaykid]

looking god man

 

[Steven.]

Pic of the valve cover:

Manifold pic:

manifold on the head:

D series Throttle Rotor:

head and intake on the block:

piece of steel that took me over a hour to find in my garage:

after about 30mins of heating, cutting and grining:

Last but not least:

 

[DEEGORILLA06]

nice job on the valve cover and throttle cable holder...hey i like your flyer.....thats oldskool...lmao

 

[Blazed]

paintjob looks crispy mang

 

[EgHatch93]

Looks great! Good luck with the rebuild on the gsr...

 

[Steven.]

was looking and finishing up some of the tuck, decided to relocate the horn.

lookin good!

LOOK MA...NO WIRES
ready for OEM air box for a DIY ice box!

 

[Steven.]

teh pan...

teh hole

atleast this looks good.....wait something not looking right?

looks a little...dented...

glad its clean in there.

now i am trying to think should i powder coat my intake manifold...