EGxBru
New Member
Ok so here is my "Build Thread" for my 98 Hatch ive been building. Ive been collecting and saving parts for about 2 years. Here's a little run-down of my build. Note it is built with the intention of turbo'ing it after a few thousand miles. I personally want to break the motor in for a little while N/A. Which will give me time to gather a Turbo Setup. All work was done by myself.
b18b1 Block-
CSS (Cylinder Support System by CnCWerx of NH)
Supertech 81.5mm 10.5:1 CR pistons
Eagle H Beam Rods
B16a2 Head-
Supertech Dual Valve Springs, Retainers, Keepers, Valve guides, High Comp. Valves
Blox B N/A cams
3 Angle Valve Job
Port and Polish
Skunk 2 IM
AEM Cam Gears
AEM Fuel Rail
B&M FPR
RMF Rep Headers
DoskyFab Catch Can
Innovative Mounts
Hondata s300
Mugen Complete Radiator Hose Kit
The motor was build by CncWerx out of Kingston, NH.
Suspension/Wheels-
Yonaka One Piece Coilovers
BWR LCA
BWR Subframe Brace
BWR Rear Camber Kit
Skunk2 Front Camber Kit
Front and Rear Eibach 25mm Sway Bars
DG Industries 6 Point Brace
Roe International Adrenaline 16x7
Exterior and Interior-
Ek4 Sir Front and Rear Bumpers
Duckbill
Si Cluster
s2000 Steering Wheel
Gsr Cloth Seats
Blox Shift Knob
As of right now the car starts up and runs eveytime with no problems, im waiting on a Wideband and a few other odds and ends before i have it street tuned by my local tuner Stickerguy Tuning out of Dracut, MA
Im sure theres stuff im forgeting but i will add them as i remember. Im not going to upload a thousand pictures, but i will upload some of them. I will update this thread as i go.
Here's how I got it
Then I brought it to my shop to start the endless list of things to do.
And here is how it sits as of yesterday September 10, 2013
Thanks for reading guys!
b18b1 Block-
CSS (Cylinder Support System by CnCWerx of NH)
Supertech 81.5mm 10.5:1 CR pistons
Eagle H Beam Rods
B16a2 Head-
Supertech Dual Valve Springs, Retainers, Keepers, Valve guides, High Comp. Valves
Blox B N/A cams
3 Angle Valve Job
Port and Polish
Skunk 2 IM
AEM Cam Gears
AEM Fuel Rail
B&M FPR
RMF Rep Headers
DoskyFab Catch Can
Innovative Mounts
Hondata s300
Mugen Complete Radiator Hose Kit
The motor was build by CncWerx out of Kingston, NH.
Suspension/Wheels-
Yonaka One Piece Coilovers
BWR LCA
BWR Subframe Brace
BWR Rear Camber Kit
Skunk2 Front Camber Kit
Front and Rear Eibach 25mm Sway Bars
DG Industries 6 Point Brace
Roe International Adrenaline 16x7
Exterior and Interior-
Ek4 Sir Front and Rear Bumpers
Duckbill
Si Cluster
s2000 Steering Wheel
Gsr Cloth Seats
Blox Shift Knob
As of right now the car starts up and runs eveytime with no problems, im waiting on a Wideband and a few other odds and ends before i have it street tuned by my local tuner Stickerguy Tuning out of Dracut, MA
Im sure theres stuff im forgeting but i will add them as i remember. Im not going to upload a thousand pictures, but i will upload some of them. I will update this thread as i go.
Here's how I got it
Then I brought it to my shop to start the endless list of things to do.
And here is how it sits as of yesterday September 10, 2013
Thanks for reading guys!